Loading...
7 results
Search Results
Now showing 1 - 7 of 7
- Electromagnetic simulation of amorphous silicon waveguidesPublication . Lourenço, Paulo; Fantoni, Alessandro; Pinho, PedroIn the past several decades, the Finite-Difference Time-Domain (FDTD) method has become one of the most powerful numerical techniques in solving the Maxwell’s curl equations and has been widely applied to solve complex optical and photonic problems. This method divides space and time into a regular grid and simulates the time evolution of Maxwell’s equations. This paper reports some results, obtained by a set of FDTD simulations, about the characteristics of amorphous silicon waveguides embedded in a SiO2 cladding. Light absorption dependence on the material properties and waveguide curvature radius are analysed for wavelengths in the infrared spectrum. Wavelength transmission efficiency is determined analysing the decay of the light power along the waveguides and the obtained results show that total losses should remain within acceptable limits when considering curvature radius as small as 3 μm at its most.
- Finite-difference time-domain analysis of hydrogenated amorphous silicon and aluminum surface plasmon waveguidesPublication . Lourenço, Paulo; Fantoni, Alessandro; Fernandes, Miguel; Vygranenko, Yuri; Vieira, ManuelaThe large majority of surface plasmon resonance (SPR)-based devices use noble metals, namely gold or silver, in their manufacturing process. These metals present low resistivity, which leads to low optical losses in the visible and near-infrared spectrum ranges. Gold shows high environmental stability, which is essential for long-term operation, and the lower stability of silver can be overcome through the deposition of an alumina layer, for instance. However, their high cost is a limiting factor if the intended target is large-scale manufacturing. This work considers a cost-effective approach through the selection of aluminum as the plasmonic material and hydrogenated amorphous silicon instead of its crystalline counterpart. This SPR structure relies on Fano resonance to improve its response to refractive index deviations of the surrounding environment. Fano resonance is highly sensitive to slight changes of the medium, hence the reason we incorporated this interference phenomenon in the proposed sensing structure. We report the results obtained when conducting finite-difference timedomain algorithm-based simulations on this metal–dielectric–metal structure when the active metal is aluminum, gold, and silver. Then, we evaluate their sensitivity, detection accuracy, and resolution. The obtained results for our proposed sensing structure show good linearity and similar parameter performance as the ones obtained when using gold or silver as plasmonic materials.
- Simulation and analysis of surface plasmon resonance based sensorPublication . Lourenço, Paulo; Vieira, Manuela; Fantoni, AlessandroIn this paper, we will be presenting the results obtained through Finite-Difference Time Domain simulations on a photonic sensing architecture. This device consists on a dielectric/metal/dielectric sensing structure. Under adequate conditions, when electromagnetic energy strikes the different dielectrics interface, these devices develop surface plasmon resonances which are extremely sensitive to refractive index variations, thus being able to be used as sensing structures. Considering their minute dimensions, monolithic integration is attainable and by incorporating cost-effective materials in their manufacture, devices' mass production may be efficient and information and communication technological systems' resiliency will be greatly facilitated. Next, this architecture is analysed under amplitude and refractive index sensitivity perspectives, its performance is analysed and considerations about its use as a sensing device are contemplated. Finally, conclusions of our work are presented and future development directions are described.
- Simulation of an early warning fire systemPublication . Lourenço, Paulo; Fantoni, Alessandro; Vieira, ManuelaIn this paper, we will be using separate software tools (wireless network and Finite Differences Time Domain based simulators) to simulate the implementation of a wireless sensor network model based on low-rate/power transmission technology. The system operates in an unlicensed frequency range and the sensing nodes rely on surface plasmon resonance phenomenon for the detection of combustion by-products. More specifically, our simulations contemplate a system for early detection of fire in densely forested areas, which will then issue a warning in an automated way. As late detection of these events usually leads to severe flora, terrain, wild life and societal impact, an early warning system will provide better event assessment conditions, thus enabling efficient resources allocation, adequate response and would certainly be a promising improvement in minimizing such disruptive impairments.
- FDTD analysis of Aluminum/a-Si:H surface plasmon waveguidesPublication . Lourenço, Paulo; Fantoni, Alessandro; Fernandes, Miguel; Vygranenko, Yuri; Vieira, ManuelaThe large majority of surface plasmon resonance based devices use noble metals, namely gold or silver, in their manufacturing process. These metals present low resistivity, which leads to low optical losses in the visible and near infrared spectrum ranges. Gold shows high environmental stability, which is essential for long-term operation, and silver's lower stability can be overcome through the deposition of an alumina layer, for instance. However, their high cost is a limiting factor if the intended target is large scale manufacturing. In this work, it is considered a cost-effective approach through the selection of aluminum as the plasmonic material and hydrogenated amorphous silicon instead of its crystalline counterpart. This surface plasmon resonance device relies on Fano resonance to improve its response to refractive index deviations of the surrounding environment. Fano resonance is highly sensitive to slight changes of the medium, hence the reason we incorporated this interference phenomenon in the proposed device. We report the results obtained when conducting Finite-Difference Time Domain algorithm based simulations on this metal-dielectric-metal structure when the active metal is aluminum, gold and silver. Then, we evaluate their sensitivity, detection accuracy and resolution, and the obtained results for our proposed device show good linearity and similar parameter performance as the ones obtained when using gold or silver as plasmonic materials.
- Lithographic mask defects analysis on an MMI 3 dB splitterPublication . Lourenço, Paulo; Fantoni, Alessandro; Costa, João; Vieira, ManuelaIn this paper, we present a simulation study that intends to characterize the influence of defects introduced by manufacturing processes on the geometry of a semiconductor structure suitable to be used as a multimode interference (MMI) 3 dB power splitter. Consequently, these defects will represent refractive index fluctuations which, on their turn, will drastically affect the propagation conditions within the structure. Our simulations were conducted on a software platform that implements the Beam Propagation numerical method. This work supports the development of a biomedical plasmonic sensor, which is based on the coupling between propagating modes in a dielectric waveguide and the surface plasmon mode that is generated on an overlaid metallic thin film, and where the output readout is achieved through an a-Si:H photodiode. By using a multimode interference 1 × 2 power splitter, this sensor device can utilize the non-sensing arm as a reference one, greatly facilitating its calibration and enhancing its performance. As the spectral sensitivity of amorphous silicon is restricted to the visible range, this sensing device should be operating on a wavelength not higher than 700 nm; thus, a-SiNx has been the material hereby proposed for both waveguides and MMI power splitter.
- Simulation analysis of a thin film semiconductor MMI 3dB splitter operating in the visible rangePublication . Lourenço, Paulo; Fantoni, Alessandro; Vieira, ManuelaIn this paper we present a simulation study that intends to characterize the influence of defects introduced by manufacturing processes on the geometry of a semiconductor structure suitable to be used as a multimode interference (MMI) 3 dB power splitter. Consequently, these defects will represent refractive index fluctuations which, on their turn, will drastically affect the propagation conditions within the structure. Our simulations were conducted on a software platform that implements both Beam Propagation and FDTD numerical methods. This work supports the development of a biomedical plasmonic sensor, which is based on the coupling between the propagating modes in a dielectric waveguide and the surface plasmon mode that is generated on an overlaid metallic thin film, and where the output readout is achieved through an a-Si:H photodiode. By using a multimode interference 1×2 power splitter, this sensor device can utilize the non-sensing arm as a reference one, greatly facilitating its calibration and enhanced performance. Amorphous silicon can be deposited by PECVD processes at temperatures lower than 300°C, an attractive characteristic which makes it back-end compatible to CMOS fabrication processes. As the spectral sensitivity of amorphous silicon is restricted to the visible range, this sensing device should be operating on a wavelength not higher than 700 nm, thus a-SiNx has been the material hereby proposed for both waveguides and MMI power splitter.