Loading...
51 results
Search Results
Now showing 1 - 10 of 51
- Analysis of metallic nanoparticles embedded in thin film semiconductors for optoelectronic applicationsPublication . Fantoni, Alessandro; Fernandes, Miguel; Vygranenko, Yuri; Louro, Paula; Vieira, Manuela; Silva, R. P. O.; Teixeira, D.; Da Costa Ribeiro, Ana Paula; Prazeres, Duarte; Alegria, ElisabeteThis paper reports about a study of the local plasmonic resonance (LSPR) produced by metal nanoparticles embedded in a dielectric or semiconductor matrix. It is presented an analysis of the LSPR for different nanoparticle metals, shapes, and embedding media composition. Metals of interest for nanoparticle composition are Aluminum and Gold. Shapes of interest are nanospheres and nanotriangles. We study in this work the optical properties of metal nanoparticles diluted in water or embedded in amorphous silicon, ITO and ZnO as a function of size, aspect-ratio and metal type. Following the analysis based on the exact solution of the Mie theory and DDSCAT numerical simulations, it is presented a comparison with experimental measurements realized with arrays of metal nanospheres. Simulations are also compared with the LSPR produced by gold nanotriangles (Au NTs) that were chemically produced and characterized by microscope and optical measurements.
- SiC multilayer photonic structures with self optical bias amplificationPublication . Vieira, Manuela; Vieira, Manuel Augusto; Louro, Paula; Fantoni, Alessandro; Barata, Manuel; Vaz da Silva, VCharacteristics of tunable wavelength pi'n/pin filters based on a-SiC:H multilayered stacked cells are studied both experimental and theoretically. Results show that the device combines the demultiplexing operation with the simultaneous photodetection and self amplification of the signal. An algorithm to decode the multiplex signal is established. A capacitive active band-pass filter model is presented and supported by an electrical simulation of the state variable filter circuit. Experimental and simulated results show that the device acts as a state variable filter. It combines the properties of active high-pass and low-pass filter sections into a capacitive active band-pass filter using a changing photo capacitance to control the power delivered to the load.
- Indoor positioning and intuitive advertising using visible light communicationPublication . Vieira, Manuela; Vieira, Manuel; Louro, Paula; Fantoni, Alessandro; Vieira, PedroThis paper researches the applicability of an intuitive advertising system for large indoor environments using Visible Light Communication (VLC). This VLC based positioning system includes the use of the visible light signal to light the space and to transmit the information for travelers’ positioning and of advertising campaigns in the surroundings. White RGB-LEDs, whose original function is providing illumination, are used as transmitters due to the ability of each individual chip to switch quickly enough to transfer data. This functionality is used for communication where the multiplexed data can be encoded in the emitting light. The light signals emitted by the LEDs positioned in the area of the advertising campaign are interpreted directly by the customers’ receivers. A SiC optical sensor with light filtering and demultiplexing properties receives the modulated signals containing the ID and the geographical position of the LED and other information, demultiplexes and decodes the data and locates the mobile device in the environment. Different layouts are analysed: square and hexagonal meshes are tested, and a 2D localization design, demonstrated by a prototype implementation, is presented. The key differences between both topologies are discussed. For both, the transmitted information, indoor position and motion direction of the customer are determined. The results showed that the LED-aided VLC navigation system enables to determine the position of a mobile target inside the network, to infer the travel direction as a function of time and to interact with information received.
- Stacked photo-sensing devices based on SiC alloys A non-pixelled architecture for imagers and demultiplexing devicesPublication . Vieira, Manuela; Louro, Paula; Fernandes, Miguel; Fantoni, Alessandro; Vieira, Manuel Augusto; Costa, JoãoIn this review paper different designs based on stacked p-i'-n-p-i-n heterojunctions are presented and compared with the single p-i-n sensing structures. The imagers utilise self-field induced depletion layers for light detection and a modulated laser beam for sequential readout. The effect of the sensing element structure, cell configurations (single or tandem), and light source properties (intensity and wavelength) are correlated with the sensor output characteristics (light-to-dark sensivity, spatial resolution, linearity and S/N ratio). The readout frequency is optimized showing that scans speeds up to 104 lines per second can be achieved without degradation in the resolution. Multilayered p-i'-n-p-i-n heterostructures can also be used as wavelength-division multiplexing /demultiplexing devices in the visible range. Here the sensor element faces the modulated light from different input colour channels, each one with a specific wavelength and bit rate. By reading out the photocurrent at appropriated applied bias, the information is multiplexed or demultiplexed and can be transmitted or recovered again. Electrical models are present to support the sensing methodologies.
- Tuning the spectral distribution of p-i-n a-SiC : H devices for colour detectionPublication . Vieira, Manuela; Louro, Paula; Fantoni, Alessandro; Fernandes, MiguelZnO:Al/p (SiC:H)/i (Si:H)/n (SiC:H) large area image and colour sensor are analysed. Carrier transport and collection efficiency are investigated from dark and illuminated current-voltage (I-V) dependence and spectral response measurements under different optical and electrical bias conditions. Results show that the carrier collection depends on the optical bias and on the applied voltage. By changing the electrical bias around the open circuit voltage it is possible to filter the absorption at a given wavelength and so to tune the spectral sensitivity of the device. Transport and optical modelling give insight into the internal physical process and explain the bias control of the spectral response and the image and colour sensing properties of the devices.
- Surface plasmon resonance sensing structurePublication . Lourenço, Paulo; Fantoni, Alessandro; Louro, Paula; Costa, João; Vieira, ManuelaSurface Plasmon Resonance occurs when a polarized electromagnetic field strikes a metallic surface at the separation interface between metal and an insulator. This phenomenon is characterized by the conduction electrons resonant oscillation at the interface, resulting on propagating plasmon waves on the metallic surface. Since this wave is generated at the boundary between the metallic surface and the external medium, these structures are highly sensitive to alterations on the surrounding environment, namely the refractive index, and may be used in sensing structures. The large majority of these devices use noble metals, namely gold or silver, as the active material. These metals present low resistivity, which leads to low optical losses in the visible and near infrared spectrum ranges. Gold shows high environmental stability, which is essential for long-term operation, and silver’s lower stability can be overcome through the deposition of an alumina layer. However, their high cost is a limiting factor if the intended target is large scale manufacturing. In this work, we performed Finite Differences Time Domain simulations on a Surface Plasmon Resonance based sensing structure, considering cost-effective materials such as aluminium for the active metal and hydrogenated amorphous silicon for the waveguide supporting elements, and verified that these structures are able to detect refractive index variations of the surrounding environment at the 1550 µm operating wavelength. This sensing architecture has also been modelled with dispersive materials, losses included, to reflect as much as possible physical reality, revealing good performance capabilities when compared to similar noble metals based devices.
- Detection of Change in Fluorescence Between Reactive Cyan and the Yellow Fluorophores Usinga-SiC:H Multilayer TransducersPublication . Vieira, Manuela; Costa, João; Louro, Paula; Fernandes, Miguel; Fantoni, AlessandroOptical colour sensors based on multilayered a-SiC:H heterostructures can act as voltage controlled optical filters in the visible range. In this article we investigate the application of these structures for Fluorescence Resonance Energy Transfer (FRET) detection, The characteristics of a-SiC:H multilayered structure are studied both theoretically and experimentally in several wavelengths corresponding to different fluorophores. The tunable optical p-i'(a-SiC:H)-n/p-i(a-Si:H)-n heterostructures were produced by PECVD and tested for a proper fine tuning in the violet, cyan and yellow wavelengths. The devices were characterized through transmittance and spectral response measurements, under different electrical bias and frequencies. Violet, cyan and yellow signals were applied in simultaneous and results have shown that they can be recovered under suitable applied bias. A theoretical analysis supported by numerical simulation is presented.
- Indoor wayfinding using visible light communicationPublication . Vieira, Manuela; Vieira, Manuel Augusto; Louro, Paula; Fantoni, Alessandro; Vieira, PedroOptical wireless communication has been widely studied during the last years in short-range applications. This paper investigates the applicability of an intuitive wayfinding system in complex buildings using Visible Light Communication (VLC). Typical scenarios include finding places, like a particular shop or office, guiding users across different floors, through elevators and stairs. Data from the sender is encoded, modulated and converted into light signals emitted by the transmitters. Tetra-chromatic white sources are used providing a different data channel for each chip. At the receiver side, the modulated light signal, containing the ID and the 3D geographical position of the transmitter and wayfinding information, is received by SiC photodetector with light filtering and demultiplexing properties. Since lighting and wireless data communication is combined, each luminaire for downlink transmission become a single cell, in which the optical access point (AP) is located in the ceiling and the mobile users are scattered within the overlap discs of each cells underneath. The light signals emitted by the LEDs are interpreted directly by the receivers of the users positioned underneath. The effect of the location of the Aps is evaluated and a model for the different cellular networks is analyzed. Orthogonal topologies are tested, and a 3D localization design, demonstrated by a prototype implementation, is presented. Uplink transmission is implemented and the 3D best route to navigate through venue calculated. Buddy wayfinding services are also implemented. The results showed that the system make possible to determine the position of a mobile target inside the network, to infer the travel direction along the time and to interact with information received and to optimize the route towards a static or dynamic destination.
- Wayfinding services in crowded buildings through visible lightPublication . Vieira, Manuela; Vieira, Manuel; Louro, Paula; Fantoni, Alessandro; Vieira, PedroThis paper investigates the applicability of an intuitive risk of transmission wayfinding system in public spaces, virtual races, indoor large environments and complex buildings using Visible Light Communication (VLC). Typical scenarios include: finding places, like a particular shop or office, guiding users across different floors, and through elevators and stairs. The system is able to inform the users, in real time, not only of the best route to the desired destination, through a route without clusters of users, but also of crowded places. Data from the sender is encoded, modulated and converted into light signals emitted by the transmitters. Tetra-chromatic white sources are used providing a different data channel for each chip. At the receiver side, the modulated light signal, containing the ID and the 3D geographical position of the transmitter and wayfinding information, is received by a SiC optical sensor with light filtering and demultiplexing properties. Since lighting and wireless data communication is combined, each luminaire for downlink transmission becomes a single cell, in which the optical Access Point (AP) is located in the ceiling and the mobile users are scattered across the overlap discs of each cell, underneath. The light signals emitted by the LEDs are interpreted directly by the receivers of the positioned users. Bidirectional communication is tested. The effect of the location of the Aps is evaluated and a 3D model for the cellular network is analyzed. In order to convert the floorplan to a 3D geometry, a tandem of layers in a orthogonal topology is used, and a 3D localization design, demonstrated by a prototype implementation, is presented. Uplink transmission is implemented, and the 3D best route to navigate through venue is calculated. Buddy wayfinding services are also considered. The results showed that the dynamic VLC navigation system enables to determine the position of a mobile target inside the network, to infer the travel direction along the time, to interact with received information and to optimize the route towards a static or dynamic destination.
- Geolocation and communication in unfamiliar indoor environments through visible lightPublication . Vieira, Manuela; Vieira, Manuel; Louro, Paula; Fantoni, Alessandro; Vieira, PedroTo support people’s wayfinding activities in unfamiliar indoor environments, a method able to generate ceiling landmark route instructions using Visible Light Communication (VLC) is proposed. The system is composed of several transmitters (ceiling luminaries) which send the map information and path messages required to wayfinding. Mobile optical receivers, using joint transmission, extracts theirs location to perform positioning and, concomitantly, the transmitted data from each transmitter. Bidirectional communication between the emitters and the receivers is available in strategic optical access point. Typical scenarios are simulated and include finding places and guiding users across different floors. Data from the sender is encoded, modulated and converted into light signals emitted by the transmitters. Tetra-chromatic white sources are used, providing a different data channel for each chip. At the receiver, the modulated light signal, containing the ID and the 3D geographical position of the transmitter and wayfinding information, is received by SiC photodetectors with light filtering and demultiplexing properties. Since lighting and wireless data communication is combined, each luminaire for downlink transmission become a single cell, in which the optical access point (AP) is located. The coded light signals are interpreted directly by the receivers of the users positioned underneath. The effect of the location of the APs is evaluated and a model for the different cellular networks is analyzed. Orthogonal and hexagonal topologies are tested, and a 3D localization design, demonstrated by a prototype is presented. Uplink transmission is implemented and the 3D best route to navigate through venue calculated. The results show that the system make possible to determine the position of a mobile target inside the network, to infer the travel direction along the time and to interact with information received and optimize the route towards a static or dynamic destination.