Loading...
4 results
Search Results
Now showing 1 - 4 of 4
- Hybrid Sepic-Ćuk DC-DC Converter Associated to a SRM Drive for a Solar PV Powered Water Pumping SystemPublication . Cordeiro, Armando; Chaves, Miguel; Canacsinh, Hiren; Luís, Ricardo; Fernao Pires, Vitor; Foito, Daniel; Pires, A. J.; Martins, JoaoThe present paper describes a solar photovoltaic (SPV) powered water pumping system employing a switched reluctance motor (SRM) and a merged Sepic-Ćuk DC-DC converter. The proposed solution was designed to use efficiently the available solar energy in order to supply water pumping systems. Solutions of this kind assume a special importance in the current scenario of natural and renewable resources optimization. The proposed DC-DC converter operates in continuous conduction mode (CCM), which combined with a maximum power point tracking (MPPT) controller, helps to optimize the power of the solar photovoltaic panel (SPV). The proposed DC-DC topology is characterized by high voltage static gain when compared with the classical boost topology and reduced voltage stress across the power switch and diodes. Several simulation and experimental results are presented in order to confirm the characteristics of the proposed solution for water pumping systems.
- A SRM for a PV powered water pumping system based on a multilevel converter and DC/DC dual output converterPublication . Foito, Daniel; Fernao Pires, Vitor; Cordeiro, Armando; Amaral, Tito; Chaves, Miguel; Pires, Armando; Martins, JoaoThis paper focuses on a proposal for a system based on a photovoltaic (PV) supply for a powered water pumping. The system consists in a switched reluctance machine (SRM) controlled by a multilevel converter and fed by PV panels associated to a DC/DC converter. The multilevel power converter proposed to control the SRM was designed to minimize the switches and to support the balance of the two input capacitors. The DC/DC converter consists in a hybrid solution that merges a Buck-Boost converter with a Sepic converter. They use a topology solution in which the input current presents a reduced ripple and only requires one switch. This DC/DC converter is also characterized by a dual output to adapt to the multilevel converter. The control system and a maximum power point tracking (MPPT) algorithm are also presented. The operation of this system will be verified by tests that are done by computer simulations.
- PV generator-fed water pumping system based on a SRM with a multilevel fault-tolerant converterPublication . Fernao Pires, Vitor; Foito, Daniel; Cordeiro, Armando; Chaves, Miguel; Pires, Armando J.This paper presents a pumping system supplied by a PV generator that is based on a switched reluctance machine (SRM). Water pumping systems are fundamental in many applications. Most of them can be used only during the day; therefore, they are highly recommended for use with PV generators. For the interface between the PV panels and the motor, a new multilevel converter is proposed. This converter is designed in order to ensure fault-tolerant capability for open switch faults. The converter is based on two three-level inverters, with some extra switches. Moreover, to reduce the number of switches, the converter is designed to provide inverse currents in the motor windings. Due to the characteristics of this motor, the inverse currents do not change the torque direction. In this way, it was possible to obtain an SRM drive with fault-tolerant capability for transistor faults; it is also a low-cost solution, due to the reduced number of switches and drives. These characteristics of fault-tolerant capability and low cost are important in applications such as water pumping systems supplied by PV generators. The proposed system was verified by several tests that were carried out by a simulation program. The experimental results, obtained from a laboratory prototype, are also presented, with the purpose of validating the simulation tests.
- Combining power electronic converters and automation to simulate solar PV systemsPublication . Cordeiro, Armando; Chaves, Miguel; Gamboa, Paulo; Barata, Filipe; Fonte, Pedro M; Lopes, Hélio; Fernao Pires, Vitor; Foito, Daniel; Amaral, Tito; Martins, JoaoThis paper presents a solar photovoltaic panel simulator system with the ability to perform automatic tests in different condition according to manufacture parameters. This simulator is based on three buck-boost DC-DC converters controlled by a microcontroller and supported by a Programmable Logic Controller which is responsible for the automatic tests. This solution will allow to achieve fast response, like suddenly changes in the irradiation, temperature, or load. To control the power converter, it will be used a fast and robust sliding mode controller. Therefore, with the proposed system is possible to perform the I-V curve simulation of a solar PV panel, evaluate different MPPT algorithms considering different meteorological and load variation. The main advantage of this work is the possibility to evaluate and test several MPPT algorithms and understand the operation and typical operation of solar PV panels in different conditions. Several simulations and experimental results from a laboratory prototype are presented to confirm the theoretical operation.